ResoBacker boards are a range of cement based water resistant tile backerboards for tile and stone applications.
The boards have high flexural and compressive strength, providing an optimum tile bonding surface in combination with its Mouldblock technology.

ResoBacker boards composition comprises of Portland cement, sand, cellulose and selected additives. They don’t contain asbestos, gypsum, glass fibre or formaldehyde.

They meet the European standard for fibre cement EN12467 and its reaction to fire, in accordance with EN13501-1, is A1, S1-d0. The product is classified as fully non-combustible.

Board Specifications

• 1200mm x 900mm (1.08m²)
• 6mm Thick
• 9kg Board Weight
• Compressive Strength 48Mpa
• Thermal Conductivity 0.216 W/mxK
• Thermal Resistance 0.0278 m².K/W
• Warm Water Resistance EN12467:2012+A2:2018 RL > 0.75
• Heat/Rain Resistance EN12467:2012+A2:2018 No Performance Determined
• Freeze/Thaw Resistance EN12467:2012+A2:2018 RL > 0.75
• Soak/Dry Resistance EN12467:2012+A2:2018 RL > 0.75
• Reaction To Fire Non-combustible, A1 Class (according to EN 13501-1 & BS EN 13501-1)
• 42 screws per boards
• If using as part of the chipboard system – please refer to the manufacturers installation notes, available on the main page.

NOTE: THIS ITEM REQUIRES PALLET DELIVERY

NOTE: Qty42 5mm x 25mm Wood Screws are required per board to affix these overlay boards to the chipboard panels

The post Printed UFH Overlay Boards – 1200mm x 900mm – 150mm Centres appeared first on The Underfloor Heating Site.

Underfloor Heating Boards – grooved chipboard for underfloor heating 22mm pre routed

• Tongue and groove for faster installation all the way around – true TG4
• 22mm P5 Moisture Resistant Chipboards Foil Coated
• 8mm Resilient Fleece layer bonded underneath
• 1.44m2 Per Board for use with 16mm Pipe Only
• Routed with 150mm or 200m centres
• Feed pipes typically run underneath
• A 6mm cement backer board must bonded to the Chip Board Panel before fitting finished floors – Sold Separately

Moisture resistant routed chipboard, available standard, foiled, or bonded to additional thermal or acoustic insulation. Our Chip-UFH Board is highly conductive which allows for an even spread of heat throughout the floor. System should be completed with Overlay Board or suitable plywood, further details available on request. The board size is 1200mm x 600mm x 22mm, being grooved on one face as required to suit 12mm diameter underfloor heating pipes, with radius returns as standard.
INSTALLATION Chip-UFH Board is typically installed directly onto floor joists (usually insulated in-between), utilising standard chipboard screws and joint adhesive.
FINISHING An Overlay Board or suitable plywood should be applied prior to the application of any floor finishes. Overlay Board is installed as a floating floor, plywood should be installed using suitable fixings. Laminates, hardwood flooring and carpets should be applied using a suitable underlay as per manufactures instructions.
SUITABLE FOR Chip-UFH Board is suitable for new build or retro fit installations, and the standard pattern board is normally available from stock.

MINIMUM ORDER 15 BOARDS

PLEASE NOTE: DELIVERY OF THESE BOARDS MAY TAKE 3-4 WORKING DAYS

The post FlowDeck36 – Foiled Chipboard With 8mm Fleece – 16mm Pipe – 2400mm x 600mm x 30mm – 150mm Centres appeared first on The Underfloor Heating Site.

Underfloor Heating Boards – grooved chipboard for underfloor heating 22mm pre routed

• Tongue and groove for faster installation all the way around – true TG4
• P5 Moisture Resistant Chipboards
• 8mm Resilient Fleece layer bonded underneath
• 1.44m2 Per Board for use with 16mm Pipe Only
• Routed with 150mm centres
• Feed pipes typically run underneath
• A 6mm cement backer board must bonded to the Chip Board Panel before fitting finished floors – Sold Separately
• Options for foiled and bonded thermal or acoustic insulation

Moisture resistant routed chipboard, available standard, foiled, or bonded to additional thermal or acoustic insulation. Our Chip-UFH Board is highly conductive which allows for an even spread of heat throughout the floor. System should be completed with Overlay Board or suitable plywood, further details available on request. The board size is 1200mm x 600mm x 22mm, being grooved on one face as required to suit 16mm diameter underfloor heating pipes, with radius returns as standard.
INSTALLATION Chip-UFH Board is typically installed directly onto floor joists (usually insulated in-between), utilising standard chipboard screws and joint adhesive.
FINISHING An Overlay Board or suitable plywood should be applied prior to the application of any floor finishes. Overlay Board is installed as a floating floor, plywood should be installed using suitable fixings. Laminates, hardwood flooring and carpets should be applied using a suitable underlay as per manufactures instructions.
SUITABLE FOR Chip-UFH Board is suitable for new build or retro fit installations, and the standard pattern board is normally available from stock.

MINIMUM ORDER 15 BOARDS

PLEASE NOTE: DELIVERY OF THESE BOARDS MAY TAKE 3-4 WORKING DAYS

The post FlowDeck36 – Chipboard With 8mm Fleece – 16mm Pipe – 2400mm x 600mm x 30mm – 150mm Centres appeared first on The Underfloor Heating Site.

Underfloor Heating Boards – grooved chipboard for underfloor heating 22mm pre routed

• Tongue and groove for faster installation all the way around – true TG4
• P5 Moisture Resistant Chipboards
• Bonded with 8mm ResoRubber base layer to the underside for acoustic sound deadening
• 1.44m2 Per Board for use with 12mm or 16mm Pipe Only
• Routed with 150mm or 200m centres
• Feed pipes typically run underneath
• Options for foiled and bonded thermal or acoustic insulation

Moisture resistant routed chipboard, available standard, foiled, or bonded to additional thermal or acoustic insulation. Our Chip-UFH Board is highly conductive which allows for an even spread of heat throughout the floor. System should be completed with Overlay Board or suitable plywood, further details available on request. The board size is 1200mm x 600mm x 22mm, being grooved on one face as required to suit 12mm diameter underfloor heating pipes, with radius returns as standard.

INSTALLATION Chip-UFH Board is typically installed directly onto floor joists (usually insulated in-between)

FINISHING An Overlay Board or suitable plywood should be applied prior to the application of any floor finishes. Overlay Board is installed as a floating floor, plywood should be installed using suitable fixings. Laminates, hardwood flooring and carpets should be applied using a suitable underlay as per manufactures instructions.

SUITABLE FOR Chip-UFH Board is suitable for new build or retro fit installations, and the standard pattern board is normally available from stock.

PLEASE NOTE: DELIVERY OF THESE BOARDS MAY TAKE 3-4 WEEKS

The post Foiled Underfloor Heating Chipboard Db Acoustic – 12mm or 16mm Pipe – 2400mm x 600mm x 30mm – includes an 8mm Bonded Rubber Base Layer appeared first on The Underfloor Heating Site.

Underfloor Heating Boards – grooved chipboard for underfloor heating 22mm pre routed

• Tongue and groove for faster installation all the way around – true TG4
• P5 Moisture Resistant Chipboards
• 1.44m2 Per Board for use with 12mm or 16mm Pipe Only
• Routed with 150mm or 200m centres
• Feed pipes typically run underneath
• A 6mm cement board must be glued and screwed as per manufacturers instruction to bring back structural strength before fitting finished floors
• Options for foiled and bonded thermal or acoustic insulation

Technical Data:

• Thermal Conductivity: 0.033 W/mK (when bonded to XPS)
• Moisture Absorption: 0.6%
• Widths Available: 600mm
• Lengths Available: 1200mm / 2400mm
• Dimensional Tolerances: (+/-1mm)
• Compressive Strength: 300kPa, 500kPa

Moisture resistant routed chipboard, available standard, foiled, or bonded to additional thermal or acoustic insulation. Our Chip-UFH Board is highly conductive which allows for an even spread of heat throughout the floor. System should be completed with 6mm cement backer board, further details available on request.

INSTALLATION Chip-UFH Board is typically installed directly onto floor joists (usually insulated in-between), utilising standard chipboard screws and joint adhesive.

FINISHING A 6mm cement overlay board should be applied using co-polymer eva glue and screws prior to the application of any floor finishes. Laminates, hardwood flooring and carpets should be applied using a suitable underlay as per manufactures instructions. LVT type flooring normally requires a 2-3mm levelling compound applied to the cement backer board to smooth out join lines and screw heads.

SUITABILITY Chip-UFH Board is suitable for new build or retro fit installations, and the standard pattern board is normally available from stock.

PLEASE NOTE: DELIVERY OF THESE BOARDS MAY TAKE 3-4 WORKING DAYS

The post Underfloor Heating Chipboard – 12mm or 16mm Pipe – 1200mm or 2400mm x 600mm x 22mm appeared first on The Underfloor Heating Site.

Underfloor Heating Boards – grooved chipboard for underfloor heating 22mm pre routed

• Tongue and groove for faster installation all the way around – true TG4
• P5 Moisture Resistant Chipboards
• 1.44m2 Per Board for use with 12mm or 16mm Pipe Only
• Routed with 150mm or 200m centres
• Feed pipes typically run underneath
• A 6mm cement board must be glued and screwed as per manufacturers instruction to bring back structural strength before fitting finished floors
• Options for foiled and bonded thermal or acoustic insulation

Technical Data:

• Thermal Conductivity: 0.033 W/mK (when bonded to XPS)
• Moisture Absorption: 0.6%
• Widths Available: 600mm
• Lengths Available: 1200mm / 2400mm
• Dimensional Tolerances: (+/-1mm)
• Compressive Strength: 300kPa, 500kPa

Moisture resistant routed chipboard, available standard, foiled, or bonded to additional thermal or acoustic insulation. Our Chip-UFH Board is highly conductive which allows for an even spread of heat throughout the floor. System should be completed with 6mm cement backer board, further details available on request.

INSTALLATION Chip-UFH Board is typically installed directly onto floor joists (usually insulated in-between), utilising standard chipboard screws and joint adhesive.

FINISHING A 6mm cement overlay board should be applied using co-polymer eva glue and screws prior to the application of any floor finishes. Laminates, hardwood flooring and carpets should be applied using a suitable underlay as per manufactures instructions. LVT type flooring normally requires a 2-3mm levelling compound applied to the cement backer board to smooth out join lines and screw heads.

SUITABILITY Chip-UFH Board is suitable for new build or retro fit installations, and the standard pattern board is normally available from stock.

PLEASE NOTE: DELIVERY OF THESE BOARDS MAY TAKE 4-5 WORKING DAYS

The post Foiled Underfloor Heating Chipboard – 12mm or 16mm Pipe – 1200mm or 2400mm x 600mm x 22mm appeared first on The Underfloor Heating Site.

• 1 x 1kg Bottles (covers approx. 30m²)

The post D3 PVA Wood Joint Glue For Gluing Chipboard UFH Joints – 1kg Bottle appeared first on The Underfloor Heating Site.

RESOBOND EVA Co-Polymer Adhesive is a high performance EVA adhesive, specifically formulated for laminating applications.

It provides excellent adhesion when bonding a porous (i.e. wood/gypsum based board) to non porous (i.e. aluminum foil) surface.

Can be applied by conventional roller systems or by hand using supplied poly bottle and nozzle.

• 1 x 1kg Bottles (covers 5m² to 7m²)

Preparation & Application

Ensure all substrates and surfaces are free from dust, dirt and other deposits.

Can be applied by roller or simply by cutting the top nozzle off to create a 3-4mm opening bead.

Pressing: Lay the items to be bonded together within the workable open time and closed assembly time and press them for as long a time as is needed to achieve the required initial firmness upon release. The pressure should be high enough to ensure contact of all parts over the entire area of the joint. Depending on the material and the type of bond being used, the mechanical firmness required for further processing of the parts is achieved within the shortest possible space of time. The highest levels of water resistance form more slowly and should be tested not earlier than 7 days after bonding.

The post EVA Co-Polymer Adhesive – 1kg Bottle – High Performance Glue For Bonding Porous To Non Porous Surfaces appeared first on The Underfloor Heating Site.

RESOBOND EVA Co-Polymer Adhesive is a high performance EVA adhesive, specifically formulated for laminating applications.

It provides excellent adhesion when bonding a porous (i.e. wood/gypsum based board) to non porous (i.e. aluminum foil) surface.

Can be applied by conventional roller systems or by hand using supplied poly bottle and nozzle.

25kg Drum  (covers c125m²)

Preparation & Application

Ensure all substrates and surfaces are free from dust, dirt and other deposits.

Application – TBC

Pressing: Lay the items to be bonded together within the workable open time and closed assembly time and press them for as long a time as is needed to achieve the required initial firmness upon release. The pressure should be high enough to ensure contact of all parts over the entire area of the joint. Depending on the material and the type of bond being used, the mechanical firmness required for further processing of the parts is achieved within the shortest possible space of time. The highest levels of water resistance form more slowly and should be tested not earlier than 7 days after bonding.

The post EVA Co-Polymer Adhesive – 25kg Drum 125m2 Coverage – High Performance Glue For Bonding Porous To Non Porous Surfaces appeared first on The Underfloor Heating Site.

• 5mm x 80mm wood screws
• 200 pieces per box
• Supplier/brand may vary

Note: Required number of screws to affix routed chipboard to joist is 12 per board for 400m centre joists, 8 per board for 600mm centre joists.

The post 5mm x 80mm Wood Screws For Fixing Routed Chipboards to joists 200pcs appeared first on The Underfloor Heating Site.